Suche
Unten sind die Ergebnisse Ihrer Suche gelistet.
Passende Seitennamen:
- CLTdesigner User manual
- Module "Compression perpendicular to grain"
- Module "Horizontal load distribution on shear walls"
- Module "CLT-Plate loaded in plane"
- Module "CLT-Plate 1D - Continuous beam"
- Module „CLT-Plate 1D - Internal forces“
- Module "SHERPA CLT-Connector"
- Module "Stiffness matrix"
- Module "Ribbed slab"
- Module "Wall"
Volltextergebnisse:
- Module "CLT-Plate 1D - Continuous beam" @en:clt:hotspot:software:cltdesigner:manual
- ncluding a cantilever on the left and right side can be analysed. The supporting width and span of field (via x-value in the table) can be defined within this input field. {{ en:clt:hotspot:softwa... tem}} ==== Cross section ==== The cross section can be defined by the user or by choosing a typical c
- CLTdesigner User manual
- untime Environment (JRE 8) A free version of JRE can be downloaded from www.java.com/download/.\\ How... rther details to implemented calculation methods can be found [[theory|here]]. ==== Standards and guid... in other languages are translations of the Austrian version. Therefore, any potential dissimilarities... to translation are identified, the version in German shall take precedence. ===== General Program bui
- Module "Horizontal load distribution on shear walls" @en:clt:hotspot:software:cltdesigner:manual
- l forces ==== The quantity of horizontal forces can be specified by entering H<sub>x</sub> and H<sub>y</sub> in [kN]. The position of the forces can be either user-defined (H<sub>x</sub> along the l... oben_button.png?40&nolink|}}, the selected point can be moved up in the sequence. * By clicking {{:c... nten_button.png?40&nolink|}}, the selected point can be moved down in the sequence. {{ en:clt:hotspot
- Module "Wall" @en:clt:hotspot:software:cltdesigner:manual
- only rectangular wall elements without openings can be calculated. The wall is defined via a wall hei... tered, are at design level. The following loads can be applied: * vertical load q<sub>d</sub> * h... esign factors}} Should it be necessary to define an eccentric load application of q<sub>d</sub>, the input of e<sub>qd</sub> can be displayed by pressing the button {{:en:clt:hot
- Instructions for download and installation
- dex.php?id=139&L=2|Download]] of the CLTdesigner can be started. ===== Download and first start of the... g?600 |Download}} After logging in, the program can be started by pressing the [[http://www.cltdesign... on of Java 8 is required. A free version of Java can be downloaded from www.java.com/download/.\\ How... Viewer and by clicking on the green start button an online search for updates on the CLTdesigner is s
- Module "Compression perpendicular to grain" @en:clt:hotspot:software:cltdesigner:manual
- pe of load configuration * calculation options An option for a quick control of the input data is o... * possible occurrence of gaps or cracks wider than 1 mm. ==== Load data and design factors ==== The... ign value) in [N], as well as the design factors can be specified here. {{ en:clt:hotspot:software:cl... load introduction above and below. Thereby, one can define if the load is even applied, and if so, if
- Module "SHERPA CLT-Connector" @en:clt:hotspot:software:cltdesigner:manual
- a warning message is displayed and, if possible, an alternative screw length is mentioned. {{ en:clt... be connected). The length of the inclined screws can be 100 mm, 120 mm or 140 mm, depending on require... rs such as compriband or sound insulation layers can be placed between the elements. Since the install... on wall-floor", wall height and length as well as an edge distance must be specified. When selecting t
- Module "Ribbed slab" @en:clt:hotspot:software:cltdesigner:manual
- tural system ==== In this release, only single span girder can be calculated. The supporting width and span (via x-value in the table) can be defined within this input field. {{ en:clt:hotspot:software:cltdes
- CLTdesigner - Versions and changes
- rsion |- Cross Timber Systems removed\\ - rho_mean of material Stora Enso changed | |13.07.2020 ... g fire details for company products after opening an old file\\ - fixed bug in the pdf report when sh... references: calculation of self-weight with rho_mean of material set to default\\ - fire: bug at pdf
- Help center
- allation of Java and for usage of Java Web Start can be found under https://www.java.com/en/download/h... ons.xml </WRAP> <WRAP center box 100%> === How can I run or activate Java in the browser? === https
- Module "Stiffness matrix" @en:clt:hotspot:software:cltdesigner:manual
- iffness_matrix:ergebnisse_steifigkeitsmatrix_membran.png |Stiffness matrix - Parts for loading in-plan... rt.png |Contents of the csv file}} The csv file can be imported into RFEM 5 via "Edit Surface" and th