Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
en:clt:hotspot:software:cltdesigner:manual:modul_plate_in_plane [2017/11/14 17:18] – [Modul „BSP-Scheibe“] Alexandra Thiel | en:clt:hotspot:software:cltdesigner:manual:modul_plate_in_plane [2020/10/28 10:13] (current) – Alexandra Thiel | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | FIXME **This page is not fully translated, yet. Please help completing the translation.**\\ //(remove this paragraph once the translation is finished)// | + | ====== Module |
- | + | ||
- | ====== Module | + | |
{{ en: | {{ en: | ||
- | ===== Eingabedaten | + | ===== Input data ===== |
- | Die Eingabe gliedert sich in: | + | The input is divided into: |
- | * Definition des Querschnittes | + | * definitions of the cross section |
- | * Brandangaben | + | * specification of parameters concerning structural fire design |
- | * Schnittgrößen | + | * internal forces (design values) |
- | * Bemessungsfaktoren | + | * definitions of design factors |
+ | ==== Cross section ==== | ||
- | ==== Querschnitt ==== | + | The input is the same as for the [[en: |
- | Siehe [[modul_plate1d_continuousbeam# | + | ++++ Show description | |
+ | {{section> | ||
+ | ++++ | ||
- | In diesem Modul kann die Querschnittsbreite nicht verändert werden. | + | In this module it is not possible to change the cross sectional width. |
- | ==== Brand ==== | + | ==== Fire ==== |
- | Siehe [[modul_plate1d_continuousbeam#brand|Modul Durchlaufträger]] | + | The input is the same as for the [[en: |
- | Brand links / rechts statt Brand oben / unten. | + | ++++ Show description | |
- | ==== Schnittgrößen und Bemessungsfaktoren ==== | + | {{section> |
+ | ++++ | ||
- | In der Karteikarte „Schnittgrößen, | + | Fire left / right instead of fire above and below. |
+ | ==== Internal forces and design factors ==== | ||
- | {{ clt: | + | In the tab „internal forces, stresses and utilization ratio“ it is possible to define the shear force in plane per unit length n< |
- | ===== Ergebnisse und Ausgabe | + | {{ en: |
+ | ===== Results and Output | ||
- | ==== Querschnittswerte | + | ==== Cross section values |
- | In der Karteikarte „Querschnittswerte“ können die effektiven Steifigkeiten der Scheibe für den Vollquerschnitt und im Falle einer Brandbemessung auch für den Brandquerschnitt abgerufen werden. | + | The effective stiffnesses of a plate loaded in plane are given in the tab "cross section values" |
- | {{ clt: | + | {{ en:clt: |
- | <WRAP center | + | <WRAP center info 100%> |
- | Die geringen Unterschiede zwischen der Dehnsteifigkeit | + | The small differences between the extensional stiffnesses |
</ | </ | ||
+ | ==== Summary of the results ==== | ||
- | ==== Zusammenfassung der Ergebnisse ==== | + | The calculated substituted thicknesses, |
- | In der Karteikarte „Schnittgrößen, Spannungen und Ausnutzung“ werden die berechneten Ersatzdicken, Spannungen sowie die Ausnutzungsgrade der beiden Mechanismen | + | Furthermore, the utilization ratios, that were calculated based on ETA-08/242 [(: |
- | Zum Vergleich werden auch die Ausnutzungsgrade angelehnt an ETA-08/242 [(:ref:eta_08_0242_2009)] und ETA-09/0036 [(:ref:eta_09_0036_2009)] berechnet und angezeigt. | + | {{ en:clt:hotspot:software:cltdesigner: |
- | {{ clt: | + | ~~DISCUSSION~~ |