Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision |
en:clt:hotspot:software:cltdesigner:manual:modul_plate_in_plane [2017/11/15 16:46] – [Querschnitt] Alexandra Thiel | en:clt:hotspot:software:cltdesigner:manual:modul_plate_in_plane [2018/04/03 14:26] – Alexandra Thiel |
---|
FIXME **This page is not fully translated, yet. Please help completing the translation.**\\ //(remove this paragraph once the translation is finished)// | ====== Module "CLT-Plate loaded in plane" ====== |
| |
====== Module „CLT-Plate loaded in plane“ ====== | |
| |
{{ en:clt:hotspot:software:cltdesigner:manual:modul_plate_in_plane:gesamtscheibe.png?600 |CLT-Plate loaded in plane}} | {{ en:clt:hotspot:software:cltdesigner:manual:modul_plate_in_plane:gesamtscheibe.png?600 |CLT-Plate loaded in plane}} |
==== Cross section ==== | ==== Cross section ==== |
| |
See [[modul_plate1d_continuousbeam#cross_section|Module CLT-Plate 1D - Continuous beam]] | The input is the same as for the [[en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam|Module "CLT-Plate 1D - Continuous beam"]]. |
| |
In diesem Modul kann die Querschnittsbreite nicht verändert werden. | ++++ Show description | |
==== Brand ==== | {{section> en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam#cross_section&inline&permalink&noheader}} |
| ++++ |
| |
Siehe [[modul_plate1d_continuousbeam#brand|Modul Durchlaufträger]] | In this module it is not possible to change the cross sectional width. |
| ==== Fire ==== |
| |
Brand links / rechts statt Brand oben / unten. | The input is the same as for the [[en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam|Module "CLT-Plate 1D - Continuous beam"]]. |
==== Schnittgrößen und Bemessungsfaktoren ==== | |
| |
In der Karteikarte „Schnittgrößen, Spannungen und Ausnutzung“ können die Schubkraft pro Einheitslänge in der Scheibenebene n<sub>xy,d</sub>, sowie die Bemessungsfaktoren festgelegt. Die der Bemessungsmethode zugrundeliegende Brettbreite ist mit 150 mm fixiert. | ++++ Show description | |
| {{section> en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam#fire&inline&permalink&noheader}} |
| ++++ |
| |
{{ clt:hotspot:software:cltdesigner:manual:modul_plate_in_plane:schnittkrafteingabe_scheibe.png |Schnittkrafteingabe}} | Fire left / right instead of fire above and below. |
| ==== Internal forces and design factors ==== |
| |
===== Ergebnisse und Ausgabe ===== | In the tab „internal forces, stresses and utilization ratio“ it is possible to define the shear force in plane per unit length n<sub>xy,d</sub>, as well as the design factors. The design method is based on a board width which is chosen when defining the cross section. |
| |
==== Querschnittswerte ==== | {{ en:clt:hotspot:software:cltdesigner:manual:modul_plate_in_plane:schnittkrafteingabe_scheibe.png |Input - internal forces and design factors}} |
| ===== Results and Output ===== |
| |
In der Karteikarte „Querschnittswerte“ können die effektiven Steifigkeiten der Scheibe für den Vollquerschnitt und im Falle einer Brandbemessung auch für den Brandquerschnitt abgerufen werden. | ==== Cross section values ==== |
| |
{{ clt:hotspot:software:cltdesigner:manual:modul_plate_in_plane:querschnittswerte_scheibe.png?600 |Querschnittswerte}} | The effective stiffnesses of a plate loaded in plane are given in the tab "cross section values" for the full cross section and in case of structural fire design for the charred cross section. |
| |
| {{ en:clt:hotspot:software:cltdesigner:manual:modul_plate_in_plane:querschnittswerte_scheibe.png |Cross section values}} |
| |
<WRAP center round info 100%> | <WRAP center round info 100%> |
Die geringen Unterschiede zwischen der Dehnsteifigkeit D<sub>x</sub> bzw. D<sub>y</sub> und der effektiven Dehnsteifigkeit EA<sub>ef</sub> im Modul BSP-Platte 1D resultieren aus der Vernachlässigung der Dehnsteifigkeiten der Querlagen in diesem Modul. | The small differences between the extensional stiffnesses D<sub>x</sub> and D<sub>y</sub> and the effective extensional stiffness EA<sub>ef</sub> in the module CLT-Plate 1D result from the negligence of the extensional stiffness of the cross layers in this module. |
</WRAP> | </WRAP> |
| |
| ==== Summary of the results ==== |
| |
==== Zusammenfassung der Ergebnisse ==== | The calculated substituted thicknesses, stresses as well as utilization ratios of the two mechanisms (Mechanism I – shear and Mechanism II – torsion) are given in the tab "internal forces, stresses and utilization ratios". |
| |
In der Karteikarte „Schnittgrößen, Spannungen und Ausnutzung“ werden die berechneten Ersatzdicken, Spannungen sowie die Ausnutzungsgrade der beiden Mechanismen (Mechanismus – Schub und Mechanismus – Torsion) angezeigt. | |
| |
Zum Vergleich werden auch die Ausnutzungsgrade angelehnt an ETA-08/242 [(:ref:eta_08_0242_2009)] und ETA-09/0036 [(:ref:eta_09_0036_2009)] berechnet und angezeigt. | Furthermore, the utilization ratios, that were calculated based on ETA-08/242 [(:ref:eta_08_0242_2009)] and ETA-09/0036 [(:ref:eta_09_0036_2009)] are given. |
| |
{{ clt:hotspot:software:cltdesigner:manual:modul_plate_in_plane:zusammenfassung_scheibe.png?600 |Zusammenfassung der Ergebnisse}} | {{ en:clt:hotspot:software:cltdesigner:manual:modul_plate_in_plane:zusammenfassung_scheibe.png |Summary of the results}} |