Suche
Unten sind die Ergebnisse Ihrer Suche gelistet.
Passende Seitennamen:
Volltextergebnisse:
- CLTdesigner - Implementierte Berechnungsverfahren @clt:hotspot:software:cltdesigner
- hlaufträger" ===== * [[clt:design:plate_loaded_out_of_plane:calculation_methods|Berechnungsmethoden ... perrholz-Elemente]] * [[clt:design:plate_loaded_out_of_plane:bending|Biegung (Belastung normal zur Plattenebene)]] * [[clt:design:plate_loaded_out_of_plane:shear|Schub (Belastung normal zur Platte... randbeanspruchung]] * [[clt:design:plate_loaded_out_of_plane:deflections|Verformungen (Belastung norm
- CLTdesigner - Implemented calculation methods @en:clt:hotspot:software:cltdesigner
- inuous beam" ===== * [[clt:design:plate_loaded_out_of_plane:calculation_methods|Berechnungsmethoden ... perrholz-Elemente]] * [[clt:design:plate_loaded_out_of_plane:bending|Biegung (Belastung normal zur Plattenebene)]] * [[clt:design:plate_loaded_out_of_plane:shear|Schub (Belastung normal zur Platte... randbeanspruchung]] * [[clt:design:plate_loaded_out_of_plane:vibration|Schwingungen]] ===== Module "C
- CLTdesigner User manual @en:clt:hotspot:software:cltdesigner
- sign standards in other countries cannot be ruled out. When differences due to translation are identifi... Module „CLT-Plate 1D - Internal forces“]] carries out the required verifications of the ultimate limit ... lane|Module „CLT-Plate loaded in plane“]] carries out the required shear stress verifications for a CLT... ne load introduction or transmission) and carries out the required verifications. The [[en:clt:hotspot
- Module "CLT-Plate 1D - Continuous beam" @en:clt:hotspot:software:cltdesigner:manual
- lassification is necessary to automatically carry out calculations for different load case combinations... "Fire" a structural fire design has to be carried out. The "Fire duration" is specified in minutes and ... fication. If a structural fire design was carried out, the governing stresses in case of fire are shown
- Modul "Querdruck" @clt:hotspot:software:cltdesigner:manual
- uck - Nachweis | {{page> :clt:design:plate_loaded_out_of_plane:compression&inline&permalink}} ++++ +++... rdruckbeiwerte | {{page> :clt:design:plate_loaded_out_of_plane:compression:model_brandner_schickhofer_2
- Module "Compression perpendicular to grain" @en:clt:hotspot:software:cltdesigner:manual
- - Verification | {{page> :clt:design:plate_loaded_out_of_plane:compression&inline&permalink}} ++++ +++... e kc,90 factor | {{page> :clt:design:plate_loaded_out_of_plane:compression:model_brandner_schickhofer_2
- Module "SHERPA CLT-Connector" @en:clt:hotspot:software:cltdesigner:manual
- n layer influences the load capacity "shear force out of plane", this must be indicated via the option ... a normal force as well as to shear forces in and out of plane. The internal forces to be specified are
- Module "Stiffness matrix" @en:clt:hotspot:software:cltdesigner:manual
- ing and torsion}} === Shear for CLT-plate loaded out-of-plane === {{ en:clt:hotspot:software:cltdesig... der_ebene.png |Stiffness matrix - Parts for shear out-of-plane}} === In-plane Stiffness values === {{