en:clt:hotspot:software:cltdesigner:versions

This translation is older than the original page and might be outdated. See what has changed.

This is an old revision of the document!


FIXME This page is not fully translated, yet.

CLTdesigner - Versions and changes

Date Version Modules concerned Changes
13.04.2011 2.0 a CLT-Plate 1D - Internal forces - interaction M+N for internal forces according to 2nd order theory: no quadratic interaction if M=0
09.05.2011 2.0 b All - Cross section definition for products: Display problem fixed
09.05.2011 2.0 c,d CLT-Plate 1D - Continuous beam - KLED of imposed loads modified according to Eurocode or NA
01.06.2011 2.0 e CLT-Plate 1D - Continuous beam - PreferencesDialog: Limit-Spinner.commitEdit() invoked when pressing OK
28.06.2011 2.1 All - Products Hasslacher
- Displaying the storage location on the window
- Output of the deflection in mm in the pdf report
17.08.2011 2.1 a All - MM 7ss-layups and MOE fixed
28.02.2012 2.2 - Spanish version
- Stora Enso and Finnforest removed
- Preferred cross sections implemented
- Material according approvalsfixed
- new layups Haas (Timbory) and Hasslacher
- in-plane shear corrected for double layers
- national annex DE
- User-Preferences established
24.08.2012 3.0 - shear analogy method
- vibration verification according to Hamm/Richter and Hamm/Richter mod.
- vibration check according to ON B extended by vibration acceleration
- layups Haas and Hasslacher updated
- new material for Hasslacher according to ETA
- user-defined combination coefficients, safety factors and kdef values
- Preferences revised
03.01.2013 3.0 a - Binder removed
- Hasslacher material ETA set as default value
16.01.2013 3.1 - new KLH layups
- charring rate of KLH changed
- tensile strength of KLH changed
- Tension check for transverse layers changed
21.01.2013 3.1 a - Bug in vibration verification for cross section widths unequal 1m corrected
21.06.2013 3.2 - new Hasslacher layups
- adhesive for Hasslacher changed
- problem with tables on Mac fixed
- SLS combination problem with wind and snow when load position "Total" fixed
21.06.2013 3.2 a - problem with dead load + snow fixed
22.07.2013 3.3 - new Derix layups
- new MM layups
- Bug with dead load and ProjectPreferences fixed
- display of bef with screed fixed
12.02.2014 3.4 - new Hasslacher layups
30.04.2014 3.5 - Rolling shear strength KLH according to ETA-06/0138 (2012-2017) modified
- mistake in writing in Hasslacher layups corrected
- display problem of utilization ratios in case of fire in module "CLT-Plate 1D - internal forces" fixed
06.06.2014 3.5 a CLT-Plate 1D - Continuous beam - Bug for beams with cantilevers in showing utilization ratios fixed, as well as the differences between summary and details
21.07.2014 3.5 b - signed jar-File
07.04.2015 3.5 c - GUIPreferences user-defined cursor excluded, because error message to a user
29.07.2015 3.6 - Binder and Stora Enso layups included
- ON B1995-1-1:2014 implemented
- disregarding of short cantilevers in SLS verification
- bug with stiffness criterion (vibrations) for continuous beams fixed
29.07.2015 3.6 a - NullpointerException at VibrationCalculatorEN fixed
30.11.2015 4.0 Compression perpendicular to grain - bug in detail view according to DIN 2010 fixed
- implementation of DIN 2013
- bug when displaying the help fixed
- kmod values according to ON B 2014 adjusted
- bug when changing the calculation method fixed
- bug at buckling fixed
02.12.2015 4.0 a CLT-Plate 1D - Internal forces - saving problem and locale problem solved
09.12.2015 4.0 b - Haas layups removed
22.12.2015 4.0 c Full version - problem with layer selection for user-defined cross sections fixed
31.03.2016 4.0 d Decker, Derix - problem with decimal format in case of vibrations solved
31.03.2016 5.0 Full version, Hasslacher, MM - problem with decimal format in case of vibrations solved
- Module "Ribbed slab" implemented
06.04.2016 4.0 e Decker, Derix - bug with the loads after file opening fixed
- deleting of results if support width is changed
06.04.2016 5.0 a Full version, Hasslacher, MM - bug with the loads after file opening fixed
- deleting of results if support width is changed
01.08.2016 5.0 b Full version, Hasslacher, MM - bug with preferences after file opening fixed
- bug at ribbed slab with different GLT strength classes fixed
- calculation of in-plane shear stiffness and twisting stiffness according to ON B 1995-1-1:2015
01.08.2016 4.0 f Decker, Derix - bug with preferences after file opening fixed
- calculation of in-plane shear stiffness and twisting stiffness according to ON B 1995-1-1:2015
24.05.2017 6.0 - bug at shear stiffness of ribbed slabs fixed
- compression perpendicular to grain to one-sided load application extended
- ribbed slab: bug with too small GLT beam height fixed
- structural fire design: bug when reading the file (charring rate, heat resistant and side bonded) fixed
- Module CLT-Plate loaded in plane: fire update problem fixed
- Module "Horizontal load distribution on shear walls"
- Module "Stiffness matrix"
- Extension "Concentrated loads"
- Products of Cross Timber Systems implemented
- Products of Decker removed
- PDF-Export of detailed results
- vibration check on cantilevers
07.06.2017 6.1 - products of Decker implemented
04.07.2017 6.2 Horizontal load distribution on shear walls - Full version, Hasslacher - display bug as well as a save/open problem when adding walls fixed
10.07.2017 6.3 Full version, all company versions - linkMaterial=true
- remember material selection if new product from the same company is selected
17.07.2017 6.4 Full version, all company versions - bug fixed when opening module "internal forces" with respect to the cross section in case of fire
- fixed bug when opening a file in respect to rotated products
- preferred cross sections removed
01.09.2017 6.5 Full version, all company versions - bug with user-defined combination coefficients fixed
- bug in module "CLT-Plate loaded in-plane" - fire cross section and pdf report as well as saving - fixed
25.10.2017 6.6 Full version, all company versions - KLH-Aufbauten aktualisiert
- NA NL
- NL
- Querdruck: Begrenzung von kc90
21.12.2017 6.7 Full version, all company versions - Hasslacher-Aufbauten aktualisiert
- Bug bei Eingabe einer Breite im Modul DL
- Textfeld Abbrandrate: Wertübernahme bei Focusverlust
22.12.2017 6.7.1 Full version, Hasslacher - Hasslacher-Aufbauten 7s und 8s aktualisiert
11.01.2018 6.7.2 Full version, Hasslacher - Hasslacher-Aufbau 5s-150 hinzugefügt
11.06.2018 6.8 Full version, all company versions - Querschnittsoptimierung
- Berechnungs-Button in Toolbar
- Auswahlmöglichkeit der Sprache beim ersten Start
- Berechnung von bef bei Rippenplatte erst auf Knopfdruck
- Brand: Berechnung ta
- Bug Schubspannungen im Ausdruck korrigiert
- Bug bei den kdef-Werten in den Einstellungen behoben
- Material Derix-ETA hinzugefügt
- kcr bei Schubfestigkeit Material EN 338 und EN 14080 berücksichtigt
- Rippenplatte - schichtweiser Nachweis
- Aufbauten Piveteaubois (HEXA2)
- Querdruck nach Brandner 2018
06.08.2018 6.9 Full version, all company versions - Bug bei der Ausgabe der Materialparameter behoben
- Bug bei der Ausgabe der Querschnittswerte im Brandfall bei unterschiedlichen Berechnungsmethoden behoben
- Gamma-Methode
- neue ETA Hasslacher
- NA FR
- Aufbauten Piveteaubois (HEXA1)
19.09.2018 6.9.1 Full version, all company versions - neue Logos Hasslacher und Derix
- Einstellungen: Bug bei Auswahl Berechnungsmethode wenn Gamma nicht vorhanden, behoben
08.10.2018 6.10 Full version, all company versions - Aufbauten best wood SCHNEIDER
- pdf-Bericht: Änderungen am Seitenlayout
- Ressourcen NL ergänzt
- Ausnutzungsgrade bei Schwingungen
- Bug bei Anzeige der Ausnutzungsgrade im Brandfall im Schnittgrößenmodul behoben
- Bug im CSInputPanel bei Brand und automatischer Berechnung behoben
23.10.2018 6.10.1 Full version, all company versions - Material Radiusholz (nur in Testversion)
- Materialzuordnung HEXA1 T
- Einheiten bei Gebäudeaussteifung
- Winst,Q statt winst,G+Q bei NA FR
07.11.2018 6.10.2 Full version, Derix - Logo Derix
08.11.2018 6.10.3 Full version - Material Binder
22.11.2018 6.10.4 Full version, all company versions - w_fin und w_net,fin überarbeitet
14.12.2018 6.10.5 Full version, all company versions - Defaulteinstellung für Vernachlässigung Eigengewicht g0 geändert
- Bug bei Gamma-Methode, wenn Det=0 behoben
17.01.2019 6.10.6 Full version, all company versions - Bug bei SLS NA FR behoben
29.01.2019 6.10.7 Full version, all company versions - Übernahme SLS Limits in den Einstellungen (ohne Enter)
- Übersetzungen FR
- Bug bei wperm für Schwingungen nach DIN behoben
18.02.2019 6.10.8 Full version, all company versions - Name von MM geändert
- Querschnitt von Piveteaubois 3s 80 geändert
- Übersetzungen FR korrigiert
- Gebäudeaussteifung: Auswahl Produzenten eingebaut
11.03.2019 6.10.9 Full version, all company versions - Gebäudeaussteifung: Auswahl Drehpunkt der Wand eingebaut
- Bug beim Öffnen von Piveteaubois-Aufbauten behoben
01.04.2019 6.11 Full version, all company versions - Binderholz entfernt
- Probleme beim Öffnen von manchen Modulen behoben
02.04.2019 6.11.1 Full version, all company versions - Aufbauten-Bibliothek bearbeitet
- Effektive Breite für Steifigkeitskriterium EC5 bearbeitet (1m oder Raumbreite, wenn < 1m)
23.05.2019 6.12 Full version, all company versions - Produktaktualisierung KLH
- Materialaktualisierung Stora Enso und Hasslacher
- Nutzungsbedingungen überarbeitet
27.05.2019 6.12.1 Full version, Hasslacher - altes Material von Hasslacher entfernt
13.06.2019 6.12.2 Full version, Cross Timber Systems - altes Material von Stora Enso entfernt
- Abbrandrate CTS auf seitenverklebt geändert
- Updateproblem Abbrandrate behoben
18.07.2019 6.12.3 Full version, all company versions - überarbeitete Nutzungsbedingungen FR
- NA FR: w2 geändert - Anteil von g1,k als fragil
- Derix-Aufbauten L100-5s, L110-5s, L120-5s hinzugefügt
27.09.2019 6.13 Full version, all company versions - PDF-Bericht - Problem mit Leerseite nach dem Inhaltsverzeichnis behoben
- KLH-Material überarbeitet
- MM - Anpassung ETA (Material und Brand)
- Bug bei Abbrandraten nach Öffnen behoben
16.10.2019 6.13.1 Full version, MM - MM: Seitenverhältnis der Lamellen t/a = 4, Default-Rechenmethode GAMMA
07.01.2020 6.14 Full version, Derix - Derix: neue ETA und Aufbauten, Kleberauswahl PUR/MUF
03.02.2020 6.14.1 Full version - Produzentenauswahl korrigiert
- Material NORDIC-1950Fb-No.3 angepasst
13.02.2020 6.14.2 Full version, all company versions - Bugs Branddaten beim Umschalten der Produzenten korrigiert
09.03.2020 7.0 Full version, all company versions - Modul SHERPA CLT-Connector
- Materialbibliothek
24.03.2020 7.0.1 Full version, Cross Timber Systems, Hasslacher, MM - Modul Rippendecke: Bug beim Bericht erstellen behoben
  • en/clt/hotspot/software/cltdesigner/versions.1585141869.txt.gz
  • Last modified: 2020/03/25 14:11
  • by Alexandra Thiel