en:clt:hotspot:software:cltdesigner:manual:modul_tbeam

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
en:clt:hotspot:software:cltdesigner:manual:modul_tbeam [2017/11/16 12:21] – [Allgemeines] Alexandra Thielen:clt:hotspot:software:cltdesigner:manual:modul_tbeam [2020/03/26 11:46] (current) Alexandra Thiel
Line 1: Line 1:
-FIXME **This page is not fully translated, yet. Please help completing the translation.**\\ //(remove this paragraph once the translation is finished)// 
- 
 ====== Module "Ribbed slab" ====== ====== Module "Ribbed slab" ======
  
Line 21: Line 19:
 ==== Structural system ==== ==== Structural system ====
  
-In der vorliegenden Version können nur Einfeldträger berechnet werdenIn diesem Eingabebereich werden die Auflagerbreiten festgelegt. Über die x-Werte in der Tabelle kann auch die Spannweite verändert werden.+In this release, only single span girder can be calculatedThe supporting width and span (via x-value in the table) can be defined within this input field.
  
 {{ en:clt:hotspot:software:cltdesigner:manual:modul_tbeam:statischessystem.png |Input - structural system}} {{ en:clt:hotspot:software:cltdesigner:manual:modul_tbeam:statischessystem.png |Input - structural system}}
- 
 ==== Cross section ==== ==== Cross section ====
  
-Die Eingabe des BSP-Querschnitts (Plattenquerschnitt) erfolgt wie bei den anderen Modulen.+The input of the CLT cross section is the same as for the [[en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam|Module "CLT-Plate 1D - Continuous beam"]].
  
 ++++ Show description | ++++ Show description |
-{{section> :clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam#querschnitt&inline&permalink&noheader}}+{{section> en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam#cross_section&inline&permalink&noheader}}
 ++++ ++++
  
Line 36: Line 33:
  
 {{ en:clt:hotspot:software:cltdesigner:manual:modul_tbeam:rippenquerschnitt.png |Input - cross section of the rib}} {{ en:clt:hotspot:software:cltdesigner:manual:modul_tbeam:rippenquerschnitt.png |Input - cross section of the rib}}
- 
 ==== Loads ==== ==== Loads ====
  
-Die Eingabe der Lasten erfolgt wie beim Modul BSP-Platte 1D - Durchlaufträgerjedoch beschränkt auf Gleichlasten.+The input is the same as for the [[en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam|Module "CLT-Plate 1D - Continuous beam"]]but limited to distributed loads.
  
 ++++ Show description | ++++ Show description |
-{{section> :clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam#lasten&inline&permalink&noheader}}+{{section> en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam#loads&inline&permalink&noheader}}
 ++++ ++++
-==== Brand ==== +==== Fire ====
- +
-In diesem Modul ist derzeit keine Brandbemessung möglich.+
  
 +In this module, currently no structural fire design is possible.
 ==== Vibrations ==== ==== Vibrations ====
  
-{{section> :clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam#schwingungen&inline&permalink&noheader}}+The input is the same as for the [[en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam|Module "CLT-Plate 1D - Continuous beam"]]. 
 + 
 +++++ Show description | 
 +{{section> en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam#vibrations&inline&permalink&noheader}} 
 +++++
 ===== Results and Output ===== ===== Results and Output =====
  
 ==== Cross section values ==== ==== Cross section values ====
  
-Im oberen Bereich der Karteikarte "Querschnittswerte" werden die Steifigkeiten der BSP-Plattedes BSH-Trägers sowie der Schubfeder, welche als Eingangsparameter für die Ermittlung der mitwirkenden Breite dienen, angezeigt.+The stiffness values of the CLT-plate and the GLT-beam as well as the shear springwhich are shown in the upper section of the tab "cross-section values" are parameters for the determination of the effective width.
  
 {{ en:clt:hotspot:software:cltdesigner:manual:modul_tbeam:querschnittswerte_bsp_bsh.png |Stiffness values of the CLT plate as well as of the rib and the shear spring}} {{ en:clt:hotspot:software:cltdesigner:manual:modul_tbeam:querschnittswerte_bsp_bsh.png |Stiffness values of the CLT plate as well as of the rib and the shear spring}}
  
-Darunter können die mitwirkende Breiteder Schwerpunkt sowie die Biege- und Schubsteifigkeit des Rippenquerschnitts im Auflagerund Feldbereich abgerufen werden.+Underneaththe effective width, the center of gravity as well as the bending and shear stiffness of the T-beam at the supports and in between are shown.
  
 {{ en:clt:hotspot:software:cltdesigner:manual:modul_tbeam:querschnittswerte_auflagerbereich.png |Cross section values at supports}} {{ en:clt:hotspot:software:cltdesigner:manual:modul_tbeam:querschnittswerte_auflagerbereich.png |Cross section values at supports}}
 ==== Summary of the results ==== ==== Summary of the results ====
  
-Die Zusammenfassung der Ergebnisse ist analog zum Modul "BSP-Platte 1D – Durchlaufträger".+The summary of the results is analogous to the [[en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam|Module "CLT-Plate 1D - Continuous beam"]].
  
 ++++ Show description | ++++ Show description |
-{{page> :clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam#zusammenfassung_der_ergebnisse&inline&permalink&noheader}}+{{page> en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam#summary_of_the_results&inline&permalink&noheader}}
 ++++ ++++
  
-Unterschiede zeigen sich jedoch für ULS - Schubda für die BSP-Platte einer Rippendecke auch der Nachweis für Schub bei Belastung in der Ebene (Scheibenschub) zu führen ist.+However, there are differences for ULS - shearsince for the CLT-flange also the in-plane shear has to be considered.
  
 {{ en:clt:hotspot:software:cltdesigner:manual:modul_tbeam:zusammenfassung.png |Summary of the results}} {{ en:clt:hotspot:software:cltdesigner:manual:modul_tbeam:zusammenfassung.png |Summary of the results}}
Line 82: Line 81:
 {{page> :clt:design:tbeam:example&inline&permalink}} {{page> :clt:design:tbeam:example&inline&permalink}}
 ++++ ++++
 +
 +~~DISCUSSION~~
  • en/clt/hotspot/software/cltdesigner/manual/modul_tbeam.1510831269.txt.gz
  • Last modified: 2017/11/16 12:21
  • by Alexandra Thiel