Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
en:clt:hotspot:software:cltdesigner:manual:modul_tbeam [2017/11/15 14:41] – [Implementierte Berechnungsverfahren] Alexandra Thiel | en:clt:hotspot:software:cltdesigner:manual:modul_tbeam [2018/04/03 16:41] – [Summary of the results] Alexandra Thiel | ||
---|---|---|---|
Line 15: | Line 15: | ||
* informations about vibration parameters | * informations about vibration parameters | ||
* calculation options | * calculation options | ||
- | ==== Allgemeines | + | ==== General |
- | {{page> : | + | {{page> |
==== Structural system ==== | ==== Structural system ==== | ||
- | In der vorliegenden Version können nur Einfeldträger berechnet werden. In diesem Eingabebereich werden die Auflagerbreiten festgelegt. Über die x-Werte in der Tabelle kann auch die Spannweite verändert werden. | + | In this release, only single span girder can be calculated. The supporting width and span (via x-value in the table) can be defined within this input field. |
{{ en: | {{ en: | ||
- | |||
==== Cross section ==== | ==== Cross section ==== | ||
- | Die Eingabe des BSP-Querschnitts (Plattenquerschnitt) erfolgt wie bei den anderen Modulen. | + | The input of the CLT cross section is the same as for the [[en: |
++++ Show description | | ++++ Show description | | ||
- | {{section> | + | {{section> |
++++ | ++++ | ||
Line 36: | Line 35: | ||
{{ en: | {{ en: | ||
- | |||
==== Loads ==== | ==== Loads ==== | ||
- | Die Eingabe der Lasten erfolgt wie beim Modul BSP-Platte | + | The input is the same as for the [[en: |
++++ Show description | | ++++ Show description | | ||
- | {{section> | + | {{section> |
++++ | ++++ | ||
- | ==== Brand ==== | + | ==== Fire ==== |
- | + | ||
- | In diesem Modul ist derzeit keine Brandbemessung möglich. | + | |
+ | In this module, currently no structural fire design is possible. | ||
==== Vibrations ==== | ==== Vibrations ==== | ||
- | {{section> | + | The input is the same as for the [[en: |
+ | |||
+ | ++++ Show description | | ||
+ | {{section> | ||
+ | ++++ | ||
===== Results and Output ===== | ===== Results and Output ===== | ||
==== Cross section values ==== | ==== Cross section values ==== | ||
- | Im oberen Bereich der Karteikarte " | + | The stiffness values of the CLT-plate and the GLT-beam as well as the shear spring, which are shown in the upper section of the tab "cross-section values" |
{{ en: | {{ en: | ||
- | Darunter können die mitwirkende Breite, der Schwerpunkt sowie die Biege- und Schubsteifigkeit des Rippenquerschnitts im Auflager- und Feldbereich abgerufen werden. | + | Underneath, the effective width, the center of gravity as well as the bending and shear stiffness of the T-beam at the supports and in between are shown. |
{{ en: | {{ en: | ||
==== Summary of the results ==== | ==== Summary of the results ==== | ||
- | Die Zusammenfassung der Ergebnisse ist analog zum Modul "BSP-Platte | + | The summary of the results is analogous to the [[en: |
++++ Show description | | ++++ Show description | | ||
- | {{page> : | + | {{page> |
++++ | ++++ | ||
- | Unterschiede zeigen sich jedoch für ULS - Schub, da für die BSP-Platte einer Rippendecke auch der Nachweis für Schub bei Belastung | + | However, there are differences for ULS - shear, since for the CLT-flange also the in-plane shear has to be considered. |
{{ en: | {{ en: |