en:clt:hotspot:software:cltdesigner:manual:modul_plate_in_plane

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
en:clt:hotspot:software:cltdesigner:manual:modul_plate_in_plane [2017/11/15 16:58] – [Fire] Alexandra Thielen:clt:hotspot:software:cltdesigner:manual:modul_plate_in_plane [2020/10/28 10:13] (current) Alexandra Thiel
Line 1: Line 1:
-FIXME **This page is not fully translated, yet. Please help completing the translation.**\\ //(remove this paragraph once the translation is finished)// +====== Module "CLT-Plate loaded in plane======
- +
-====== Module CLT-Plate loaded in plane“ ======+
  
 {{ en:clt:hotspot:software:cltdesigner:manual:modul_plate_in_plane:gesamtscheibe.png?600 |CLT-Plate loaded in plane}} {{ en:clt:hotspot:software:cltdesigner:manual:modul_plate_in_plane:gesamtscheibe.png?600 |CLT-Plate loaded in plane}}
Line 14: Line 12:
 ==== Cross section ==== ==== Cross section ====
  
-See [[modul_plate1d_continuousbeam#cross_section|Module CLT-Plate 1D - Continuous beam]]+The input is the same as for the [[en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam|Module "CLT-Plate 1D - Continuous beam"]].
  
-In diesem Modul kann die Querschnittsbreite nicht verändert werden.+++++ Show description | 
 +{{section> en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam#cross_section&inline&permalink&noheader}} 
 +++++ 
 + 
 +In this module it is not possible to change the cross sectional width.
 ==== Fire ==== ==== Fire ====
  
-See [[modul_plate1d_continuousbeam#brand|Module CLT-Plate 1D - Continuous beam]]+The input is the same as for the [[en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam|Module "CLT-Plate 1D - Continuous beam"]]
 + 
 +++++ Show description | 
 +{{section> en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam#fire&inline&permalink&noheader}} 
 +++++
  
 Fire left / right instead of fire above and below. Fire left / right instead of fire above and below.
 ==== Internal forces and design factors ==== ==== Internal forces and design factors ====
  
-In the tab „internal forces, stresses and utilization ratio“ it is possible to define the shear force in plane per unit length n<sub>xy,d</sub>, as well as the design factors. The design method is based on a board width of 150 mmFIXME+In the tab „internal forces, stresses and utilization ratio“ it is possible to define the shear force in plane per unit length n<sub>xy,d</sub>, as well as the design factors. The design method is based on a board width which is chosen when defining the cross section.
  
 {{ en:clt:hotspot:software:cltdesigner:manual:modul_plate_in_plane:schnittkrafteingabe_scheibe.png |Input - internal forces and design factors}} {{ en:clt:hotspot:software:cltdesigner:manual:modul_plate_in_plane:schnittkrafteingabe_scheibe.png |Input - internal forces and design factors}}
Line 35: Line 41:
 {{ en:clt:hotspot:software:cltdesigner:manual:modul_plate_in_plane:querschnittswerte_scheibe.png |Cross section values}} {{ en:clt:hotspot:software:cltdesigner:manual:modul_plate_in_plane:querschnittswerte_scheibe.png |Cross section values}}
  
-<WRAP center round info 100%>+<WRAP center info 100%>
 The small differences between the extensional stiffnesses D<sub>x</sub> and D<sub>y</sub> and the effective extensional stiffness EA<sub>ef</sub> in the module CLT-Plate 1D result from the negligence of the extensional stiffness of the cross layers in this module. The small differences between the extensional stiffnesses D<sub>x</sub> and D<sub>y</sub> and the effective extensional stiffness EA<sub>ef</sub> in the module CLT-Plate 1D result from the negligence of the extensional stiffness of the cross layers in this module.
 </WRAP> </WRAP>
Line 46: Line 52:
  
 {{ en:clt:hotspot:software:cltdesigner:manual:modul_plate_in_plane:zusammenfassung_scheibe.png |Summary of the results}} {{ en:clt:hotspot:software:cltdesigner:manual:modul_plate_in_plane:zusammenfassung_scheibe.png |Summary of the results}}
 +
 +~~DISCUSSION~~
  • en/clt/hotspot/software/cltdesigner/manual/modul_plate_in_plane.1510761538.txt.gz
  • Last modified: 2017/11/15 16:58
  • by Alexandra Thiel