en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_internalforces

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_internalforces [2017/11/15 17:10] – [Querschnitt] Alexandra Thielen:clt:hotspot:software:cltdesigner:manual:modul_plate1d_internalforces [2020/03/26 11:45] (current) Alexandra Thiel
Line 1: Line 1:
-FIXME **This page is not fully translated, yet. Please help completing the translation.**\\ //(remove this paragraph once the translation is finished)// 
- 
 ====== Module „CLT-Plate 1D - Internal forces“ ====== ====== Module „CLT-Plate 1D - Internal forces“ ======
  
Line 15: Line 13:
 ==== Cross section ==== ==== Cross section ====
  
-See [[modul_plate1d_continuousbeam#querschnitt|Module CLT-Plate 1D - Continuous beam]] +The input is the same as for the [[en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam|Module "CLT-Plate 1D - Continuous beam"]]. 
-==== Brand ====+ 
 +++++ Show description | 
 +{{section> en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam#cross_section&inline&permalink&noheader}} 
 +++++ 
 +==== Fire ==== 
 + 
 +The input is the same as for the [[en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam|Module CLT-Plate 1D - Continuous beam]]
 + 
 +++++ Show description | 
 +{{section> en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam#fire&inline&permalink&noheader}} 
 +++++ 
 +==== Type of calculation, internal forces, design factors and specifications concerning stability ==== 
 + 
 +The internal forces and the underlying type of calculation are defined in the tab „Internal forces, stresses and utilisation ratios“. Additionally, the design values are specified here.
  
-Siehe [[modul_plate1d_continuousbeam#brand|Modul Durchlaufträger]] +If the internal forces result from a calculation based on a first order analysis a substitute buckling length has to be stated in case of a negative normal force ("problem of stability"). Based on this buckling length and the respective cross section the required buckling factor k<sub>c</sub> needed for the verification is calculated automatically.
-==== Art der Berechnung, Schnittgrößen, Bemessungsfaktoren und Stabilitätsangaben ====+
  
-In der Karteikarte „SchnittgrößenSpannungen und Ausnutzung“ können die Schnittgrößen, sowie die zugrundeliegende Berechnungsart angegeben werden. Des Weiteren werden hier die Bemessungsfaktoren festgelegt.+{{ en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_internalforces:angabencsverification.png |Input - internal forcesdesign factors and specifications concerning stability}} 
 +===== Results and output =====
  
-Wenn die Schnittgrößen aus einer Berechnung nach Theorie 1. Ordnung stammen, muss für den Fall einer negativen Normalkraft („Stabilitätsproblem“) eine Ersatzknicklänge angegeben werden. Aus dieser Knicklänge und dem jeweiligen Querschnitt wird dann automatisch der für die Nachweisführung benötigte Knickbeiwert k<sub>c</sub> ermittelt.+==== Cross section values ====
  
-{{ clt:hotspot:software:cltdesigner:manual:modul_plate1d_internalforces:angabencsverification.png |Eingabe Schnittgrößen}} +The output is the same as for the [[en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam|Module „CLT-Plate 1D - Continuous beam“]].
-===== Ergebnisse und Ausgabe =====+
  
-==== Querschnittswerte ====+++++ Show description | 
 +{{section> en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam#cross_section_values&inline&permalink&noheader}} 
 +++++ 
 +==== Summary of the results ====
  
-Siehe [[modul_plate1d_continuousbeam#querschnittswerte|Modul Durchlaufträger]] +The stress distributions and the governing utilisation ratios are shown in the tab "Internal forces, stresses and utilisation ratios".
-=== Zusammenfassung der Ergebnisse ===+
  
-In der Karteikarte „Schnittgrößen, Spannungen und Ausnutzung“ werden die Spannungsverläufe sowie die maßgebenden Ausnutzungsgrade angezeigt.+{{ en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_internalforces:ergebnissecsverification.png?600 |Summary of the results}} 
 +==== Detailed results ====
  
-{{ clt:hotspot:software:cltdesigner:manual:modul_plate1d_internalforces:ergebnissecsverification.png?600 |Zusammenfassung der Ergebnisse}} +Stresses and utilisation ratios of the single layers are shown when clicking on the "Details" button.
-==== Ergebnisse im Detail ====+
  
-Über den Button „Details“ können die Spannungen und Ausnutzungsgrade der einzelnen Schichten betrachtet werden.+{{ en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_internalforces:detailscsverification.png?600 |Detailed results}}
  
-{{ clt:hotspot:software:cltdesigner:manual:modul_plate1d_internalforces:detailscsverification.png?600 |Ergebnisse im Detail}}+~~DISCUSSION~~
  • en/clt/hotspot/software/cltdesigner/manual/modul_plate1d_internalforces.1510762255.txt.gz
  • Last modified: 2017/11/15 17:10
  • by Alexandra Thiel