Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_internalforces [2017/11/15 17:04] – [Module „CLT-Plate 1D - Internal forces“] Alexandra Thiel | en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_internalforces [2020/03/26 11:45] (current) – Alexandra Thiel | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | FIXME **This page is not fully translated, yet. Please help completing the translation.**\\ //(remove this paragraph once the translation is finished)// | ||
- | |||
====== Module „CLT-Plate 1D - Internal forces“ ====== | ====== Module „CLT-Plate 1D - Internal forces“ ====== | ||
{{ en: | {{ en: | ||
- | ===== Eingabedaten | + | ===== Input data ===== |
+ | |||
+ | The input is divided into: | ||
+ | |||
+ | * definitions of the cross section | ||
+ | * specifications concerning structural fire design | ||
+ | * internal forces according to the theory (of 1< | ||
+ | * design factors | ||
+ | * specifications concerning stability | ||
+ | ==== Cross section ==== | ||
+ | |||
+ | The input is the same as for the [[en: | ||
- | Die Eingabe gliedert sich in: | + | ++++ Show description | |
+ | {{section> | ||
+ | ++++ | ||
+ | ==== Fire ==== | ||
- | * Definition des Querschnittes | + | The input is the same as for the [[en: |
- | * Brandangaben | + | |
- | * Art der Berechnung | + | |
- | * Schnittgrößen | + | |
- | * Bemessungsfaktoren | + | |
- | * Stabilitätsangaben | + | |
- | ==== Querschnitt | + | ++++ Show description | |
+ | {{section> | ||
+ | ++++ | ||
+ | ==== Type of calculation, | ||
- | Siehe [[modul_plate1d_continuousbeam# | + | The internal forces and the underlying type of calculation are defined in the tab „Internal forces, stresses and utilisation ratios“. Additionally, |
- | ==== Brand ==== | + | |
- | Siehe [[modul_plate1d_continuousbeam# | + | If the internal forces result from a calculation based on a first order analysis a substitute buckling length has to be stated in case of a negative normal force (" |
- | ==== Art der Berechnung, Schnittgrößen, | + | |
- | In der Karteikarte „Schnittgrößen, Spannungen und Ausnutzung“ können die Schnittgrößen, | + | {{ en: |
+ | ===== Results and output ===== | ||
- | Wenn die Schnittgrößen aus einer Berechnung nach Theorie 1. Ordnung stammen, muss für den Fall einer negativen Normalkraft („Stabilitätsproblem“) eine Ersatzknicklänge angegeben werden. Aus dieser Knicklänge und dem jeweiligen Querschnitt wird dann automatisch der für die Nachweisführung benötigte Knickbeiwert k< | + | ==== Cross section values ==== |
- | {{ clt: | + | The output is the same as for the [[en:clt: |
- | ===== Ergebnisse und Ausgabe ===== | + | |
- | ==== Querschnittswerte | + | ++++ Show description | |
+ | {{section> | ||
+ | ++++ | ||
+ | ==== Summary of the results | ||
- | Siehe [[modul_plate1d_continuousbeam# | + | The stress distributions and the governing utilisation ratios are shown in the tab " |
- | === Zusammenfassung der Ergebnisse === | + | |
- | In der Karteikarte „Schnittgrößen, | + | {{ en: |
+ | ==== Detailed results ==== | ||
- | {{ clt: | + | Stresses and utilisation ratios of the single layers are shown when clicking on the " |
- | ==== Ergebnisse im Detail ==== | + | |
- | Über den Button „Details“ können die Spannungen und Ausnutzungsgrade der einzelnen Schichten betrachtet werden. | + | {{ en: |
- | {{ clt: | + | ~~DISCUSSION~~ |