Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revisionLast revisionBoth sides next revision | ||
en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_internalforces [2017/11/15 17:10] – [Querschnitt] Alexandra Thiel | en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_internalforces [2017/11/20 09:48] – [Cross section values] Alexandra Thiel | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | FIXME **This page is not fully translated, yet. Please help completing the translation.**\\ //(remove this paragraph once the translation is finished)// | ||
- | |||
====== Module „CLT-Plate 1D - Internal forces“ ====== | ====== Module „CLT-Plate 1D - Internal forces“ ====== | ||
Line 15: | Line 13: | ||
==== Cross section ==== | ==== Cross section ==== | ||
- | See [[modul_plate1d_continuousbeam# | + | The input is the same as for the [[en: |
- | ==== Brand ==== | + | |
+ | ++++ Show description | | ||
+ | {{section> | ||
+ | ++++ | ||
+ | ==== Fire ==== | ||
+ | |||
+ | The input is the same as for the [[en: | ||
+ | |||
+ | ++++ Show description | | ||
+ | {{section> | ||
+ | ++++ | ||
+ | ==== Type of calculation, | ||
- | Siehe [[modul_plate1d_continuousbeam# | + | The internal forces and the underlying type of calculation are defined in the tab „Internal forces, stresses and utilisation ratios“. Additionally, the design values are specified here. |
- | ==== Art der Berechnung, Schnittgrößen, Bemessungsfaktoren und Stabilitätsangaben ==== | + | |
- | In der Karteikarte „Schnittgrößen, | + | If the internal forces result from a calculation based on a first order analysis a substitute buckling length has to be stated in case of a negative normal force (" |
- | Wenn die Schnittgrößen aus einer Berechnung nach Theorie 1. Ordnung stammen, muss für den Fall einer negativen Normalkraft („Stabilitätsproblem“) eine Ersatzknicklänge angegeben werden. Aus dieser Knicklänge und dem jeweiligen Querschnitt wird dann automatisch der für die Nachweisführung benötigte Knickbeiwert k< | + | {{ en: |
+ | ===== Results and output ===== | ||
- | {{ clt: | + | ==== Cross section values |
- | ===== Ergebnisse und Ausgabe ===== | + | |
- | ==== Querschnittswerte ==== | + | The output is the same as for the [[en: |
- | Siehe [[modul_plate1d_continuousbeam# | + | ++++ Show description | |
- | === Zusammenfassung der Ergebnisse | + | {{section> |
+ | ++++ | ||
+ | ==== Summary of the results | ||
- | In der Karteikarte „Schnittgrößen, Spannungen und Ausnutzung“ werden die Spannungsverläufe sowie die maßgebenden Ausnutzungsgrade angezeigt. | + | The stress distributions and the governing utilisation ratios are shown in the tab " |
- | {{ clt: | + | {{ en:clt: |
- | ==== Ergebnisse im Detail | + | ==== Detailed results |
- | Über den Button „Details“ können die Spannungen und Ausnutzungsgrade der einzelnen Schichten betrachtet werden. | + | Stresses and utilisation ratios of the single layers are shown when clicking on the "Details" button. |
- | {{ clt: | + | {{ en:clt: |