en:clt:hotspot:software:cltdesigner:manual:modul_horizontal_force_distribution_on_shear_walls

This translation is older than the original page and might be outdated. See what has changed.

This is an old revision of the document!


FIXME This page is not fully translated, yet. Please help completing the translation.
(remove this paragraph once the translation is finished)

Module "Horizontal load distribution on shear walls"

Module Horizontal load distribution on shear walls

The input is divided into:

  • input of the position and quantity of acting horizontal forces
  • input of the floor polygon
  • input of the shear walls
  • calculation options

The quantity of horizontal forces can be specified by entering Hx and Hy in [kN]. The position of the forces can be either unser-defined (Hx along the line of action in yHx and Hy along the line of action in xHy) or specified at the center of mass. By selecting "at center of mass", the position of the forces will be determined from the polygon of floor.

Input of the horizontal acting forces

Input of the floor polygon

The floor is defined by entering the coordinates of the corner points. The sequence of the points must be counterclockwise and there must be no openings. The origin of the draft is shown on the upper-right corner of the window.

  • By clicking , a new corner point is created.
  • By clicking , the selected point will be deleted.
  • By clicking , the selected point can be moved up in the sequence.
  • By clicking , the selected point can be moved down in the sequence.

Floor plan with shear walls, floor polygon and acting forces

FIXME The walls can be defined using the following table. The selection of the cross-section, and thereby of the producer, is in the current calculation neglected since the stiffnesses are calculated in proportion to the wall length. The position of the wall can be defined either by specifying the reference point (the point left under at the φ = 0°; xref and yref) or by entering the center of mass (gravity???) (xC and yC), as well as the angle of rotation φ.

Die Eingabe der Wände kann in folgender Tabelle vorgenommen werden. Die Auswahl des Querschnittes und somit des Produzenten ist in der derzeitigen Berechnung unerheblich, da die Steifigkeiten nur proportional zur Wandlänge berechnet werden. Die Lage der Wände wird entweder über die Eingabe des Bezugspunktes (Punkt links unten bei φ = 0°; xref und yref) oder über Eingabe des Schwerpunktes (xC und yC) sowie dem Drehwinkel φ beschrieben.

Input of shear walls

  • Mit kann eine neue Wand erzeugt werden.
  • Mit wird die selektierte Wand gelöscht.

In der derzeitigen Version erfolgt die Berechnung der Wandsteifigkeiten (Wand inkl. Befestigung) proportional über die Wandlänge (c ∼ ℓ exp). Der Exponent exp kann hier eingestellt werden.

Calculation options

Stiffness center of walls and center of mass

Die Ausgabe erfolgt getrennt für die angreifenden Kräfte Hx und Hy sowie für die Kombination Hx + Hy. Ausgegeben wird jeweils das Moment, welches sich aus einem exzentrischen Lastangriff ergibt sowie die Kräfte auf die einzelnen Wände in ihren x- und y-Komponenten (Fx und Fy) sowie als Resultierende F unter dem Winkel αF. Zur Kontrolle werden auch noch die Summe der Kräfte in x- bzw. y-Richtung sowie die Summe der Momente überprüft.

Forces according to Hx and Hy

Eine graphische Darstellung der Ergebnisse ist im Fenster rechts unten zu sehen, wieder unterteilt in Hx, Hy und Hx + Hy.

Results according to Hx and Hy

  • en/clt/hotspot/software/cltdesigner/manual/modul_horizontal_force_distribution_on_shear_walls.1513099723.txt.gz
  • Last modified: 2017/12/12 18:28
  • by kbratulic