Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
en:clt:hotspot:software:cltdesigner:manual:modul_compression_perpendicular_to_grain [2017/12/19 14:58] – [Load configuration] kbratulic | en:clt:hotspot:software:cltdesigner:manual:modul_compression_perpendicular_to_grain [2018/04/03 17:13] – Alexandra Thiel | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | FIXME **This page is not fully translated, yet. Please help completing the translation.**\\ //(remove this paragraph once the translation is finished)// | ||
- | |||
====== Module " | ====== Module " | ||
Line 14: | Line 12: | ||
* type of load configuration | * type of load configuration | ||
* calculation options | * calculation options | ||
- | |||
- | FIXME | ||
An option for a quick control of the input data is offered by a graphical representation shown on the right side. | An option for a quick control of the input data is offered by a graphical representation shown on the right side. | ||
Line 22: | Line 18: | ||
==== Cross-section ==== | ==== Cross-section ==== | ||
- | The input is the same as for the [[en: | + | {{page> en: |
- | + | ||
- | ++++ Show description | | + | |
- | {{section> en: | + | |
- | ++++ | + | |
==== Plate dimensions and gap execution ==== | ==== Plate dimensions and gap execution ==== | ||
- | |||
- | FIXME | ||
The plate is specified with its dimensions in x and y direction. The plate length is defined with dimension in x direction and the plate width with dimension in y direction. | The plate is specified with its dimensions in x and y direction. The plate length is defined with dimension in x direction and the plate width with dimension in y direction. | ||
- | |||
- | Die Platte wird durch ihre Dimensionen in x- und y-Richtung beschrieben. Die Länge der Platte ist die Abmessung in x-Richtung und die Breite die in y-Richtung. | ||
{{ en: | {{ en: | ||
- | FIXME | + | In addition to plate dimensions, the analysis also considers the way the lamellas are joined into individual layers. |
- | + | ||
- | In addition to plate dimensions, the analysis also considers the way the lamellas are joined into individual layers. | + | |
* side gluing of lamellas, | * side gluing of lamellas, | ||
* assembly without adhesive where lamellas are placed side by side without the sheduled gaps or the expected occurence of cracks and | * assembly without adhesive where lamellas are placed side by side without the sheduled gaps or the expected occurence of cracks and | ||
* possible occurence of gaps or cracks wider than 1 mm. | * possible occurence of gaps or cracks wider than 1 mm. | ||
- | |||
- | Neben der Plattenabmessungen geht auch die Fugenausführung in die Berechnung ein. Bezüglich der Fugenausführung ist zu unterscheiden ob die Decklagen | ||
- | * seitenverklebt sind, | ||
- | * nicht seitenverklebt, | ||
- | * ob Fugen oder Risse mit größer 1 mm auftreten können. | ||
==== Load data and design factors ==== | ==== Load data and design factors ==== | ||
- | FIXME | + | The applied |
- | + | ||
- | The force being transferred | + | |
- | + | ||
- | Hier können die einzuleitende Kraft F< | + | |
{{ en: | {{ en: | ||
==== Load configuration ==== | ==== Load configuration ==== | ||
- | |||
- | FIXME | ||
The load situation is described by specifying the load introduction above and below. Thereby, one can define if the load is even applied, and if so, if it is applied locally or continuously (over entire surface). | The load situation is described by specifying the load introduction above and below. Thereby, one can define if the load is even applied, and if so, if it is applied locally or continuously (over entire surface). | ||
- | If the load is applied locally, it needs to be defined by entering the dimensions of the load surface (length l< | + | If the load is applied locally, it needs to be defined by entering the dimensions of the load surface (length l< |
- | + | ||
- | Die Lastsituation wird durch die Lasteinleitung oben und unten beschrieben. Dabei kann die Lasteinleitung lokal oder kontinuierlich (über gesamte Plattenfläche) erfolgen oder auch keine Lasteinleitung vorhanden sein. | + | |
- | + | ||
- | Bei lokaler Lasteinleitung sind die Abmessungen der Beanspruchungsfläche (Länge in x-Richtung l< | + | |
{{ en: | {{ en: | ||
Line 74: | Line 45: | ||
==== Calculation options ==== | ==== Calculation options ==== | ||
- | In den Berechnungsoptionen können die Lastausbreitungswinkel für Längslagen | + | In the calculation options, the load distribution angles for longitudinal layers |
{{ en: | {{ en: | ||
===== Results and Output ===== | ===== Results and Output ===== | ||
- | Die minimale Lasteinleitungsfläche beschreibt die Bezugsfläche, | + | The minimum load introduction area A< |
- | Die Ausnutzung auf Querdruck wird durch den Ausnutzungsgrad | + | The utilisation ratio for compression perpendicular to grain is indicated by η< |
{{ en: | {{ en: | ||
- | In der folgenden Skizze wird der Verlauf der effektiven Fläche | + | The following figure shows the distribution of the effective area A< |
{{ en: | {{ en: |