| Beide Seiten der vorigen Revision Vorhergehende Überarbeitung Nächste Überarbeitung | Vorhergehende Überarbeitung |
| en:clt:hotspot:software:cltdesigner:manual:modul_tbeam_new [2024/10/10 16:33] – [Zusammenfassung der Ergebnisse] Alexandra Thiel | en:clt:hotspot:software:cltdesigner:manual:modul_tbeam_new [2024/10/10 17:33] (aktuell) – Alexandra Thiel |
|---|
| FIXME **This page is not fully translated, yet. Please help completing the translation.**\\ //(remove this paragraph once the translation is finished)// | |
| |
| ~~NOTOC~~ | ~~NOTOC~~ |
| ====== Module "Ribbed slab" ====== | ====== Module "Ribbed slab" ====== |
| The rib cross-section (rectangular cross-section made of glulam or solid wood) is defined by entering the height and width of the rib and selecting the material. If "Standard dimensions only" is selected, the dimensions for the nearest standard cross-section are set. | The rib cross-section (rectangular cross-section made of glulam or solid wood) is defined by entering the height and width of the rib and selecting the material. If "Standard dimensions only" is selected, the dimensions for the nearest standard cross-section are set. |
| |
| {{ :en:clt:hotspot:software:cltdesigner:manual:modul_tbeam_new:rippenquerschnitt.png?411 |Input - cross section of the rib}} | {{ :en:clt:hotspot:software:cltdesigner:manual:modul_tbeam:rippenquerschnitt.png?411 |Input - cross section of the rib}} |
| |
| ==== Loads ==== | ==== Loads ==== |
| |
| The input is the same as for the [[en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam|Module "CLT-Plate 1D - Continuous beam"]], but limited to distributed loads. | The input is the same as for the Module "CLT-Plate 1D - Continuous beam", but limited to distributed loads. |
| |
| ++++ Show description | | ++++ Show description | |
| ==== Cross section values ==== | ==== Cross section values ==== |
| |
| Auf der Karteikarte "Querschnittswerte" werden die mitwirkende Breite, der Schwerpunkt sowie die Biege- und Schubsteifigkeit des Rippenquerschnitts im Auflager- und Feldbereich angezeigt. | On the tab "cross-section values", the effective width, the center of gravity as well as the bending and shear stiffness of the T-beam at the supports and in between are shown. |
| |
| {{ :clt:hotspot:software:cltdesigner:manual:modul_tbeam_new:querschnittswerte_feldbereich.png |Querschnittswerte im Feldbereich}} | {{ :en:clt:hotspot:software:cltdesigner:manual:modul_tbeam_new:querschnittswerte_feldbereich.png |Cross section values}} |
| |
| Über den Button {{:clt:hotspot:software:cltdesigner:manual:modul_tbeam_new:info_button.png?40&nolink}} können die Steifigkeiten der BSP-Platte, des BSH-Trägers sowie der Schubfeder, welche als Eingangsparameter für die Ermittlung der mitwirkenden Breite dienen, angezeigt werden. | The button {{:clt:hotspot:software:cltdesigner:manual:modul_tbeam_new:info_button.png?40&nolink}} can be used to display the stiffness values of the CLT panel, the glulam beam and the shear spring, which are the input parameters for determining the effective width. |
| |
| {{ :clt:hotspot:software:cltdesigner:manual:modul_tbeam_new:querschnittswerte_bsp_bsh.png?811 |Steifigkeiten der BSP-Platte sowie der Rippe und der Schubfeder}} | {{ :en:clt:hotspot:software:cltdesigner:manual:modul_tbeam_new:querschnittswerte_bsp_bsh.png?811 |Stiffness values of the CLT panel, the glulam beam and the shear spring}} |
| ==== Summary of the results ==== | ==== Summary of the results ==== |
| |
| However, there are differences for ULS - shear, since for the CLT-flange also the in-plane shear has to be considered. | However, there are differences for ULS - shear, since for the CLT-flange also the in-plane shear has to be considered. |
| |
| {{ :en:clt:hotspot:software:cltdesigner:manual:modul_tbeam_new:zusammenfassung.png |Summary of the results}} | {{ :en:clt:hotspot:software:cltdesigner:manual:modul_tbeam:zusammenfassung.png |Summary of the results}} |
| |