en:clt:hotspot:software:cltdesigner:manual:modul_tbeam

Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen angezeigt.

Link zu dieser Vergleichsansicht

Beide Seiten der vorigen Revision Vorhergehende Überarbeitung
Nächste Überarbeitung
Vorhergehende Überarbeitung
en:clt:hotspot:software:cltdesigner:manual:modul_tbeam [2018/04/03 16:43] Alexandra Thielen:clt:hotspot:software:cltdesigner:manual:modul_tbeam [2025/06/16 17:54] (aktuell) – [Implemented calculation methods] Alexandra Thiel
Zeile 1: Zeile 1:
 ====== Module "Ribbed slab" ====== ====== Module "Ribbed slab" ======
  
-{{ en:clt:hotspot:software:cltdesigner:manual:modul_tbeam:gesamtrippendecke.png?600 |Module Ribbed slab}}+{{ en:clt:hotspot:software:cltdesigner:manual:modul_tbeam:gesamtrippendecke.png |Module Ribbed slab}}
  
 ===== Input data ===== ===== Input data =====
Zeile 21: Zeile 21:
 In this release, only single span girder can be calculated. The supporting width and span (via x-value in the table) can be defined within this input field. In this release, only single span girder can be calculated. The supporting width and span (via x-value in the table) can be defined within this input field.
  
-{{ en:clt:hotspot:software:cltdesigner:manual:modul_tbeam:statischessystem.png |Input - structural system}}+{{ en:clt:hotspot:software:cltdesigner:manual:modul_tbeam:statischessystem.png?350 |Input - structural system}}
 ==== Cross section ==== ==== Cross section ====
  
Zeile 30: Zeile 30:
 ++++ ++++
  
-Die Definition des Rippenquerschnittes (Rechteckquerschnitt aus BSH oder Vollholzerfolgt über die Eingabe der Höhe und Breite der Rippe sowie Auswahl des Materials.+The rib cross-section (rectangular cross-section made of glulam or solid woodis defined by entering the height and width of the rib and selecting the material. If "Standard dimensions only" is selected, the dimensions for the nearest standard cross-section are set.
  
-{{ en:clt:hotspot:software:cltdesigner:manual:modul_tbeam:rippenquerschnitt.png |Input - cross section of the rib}}+{{ en:clt:hotspot:software:cltdesigner:manual:modul_tbeam:rippenquerschnitt.png?450 |Input - cross section of the rib}}
 ==== Loads ==== ==== Loads ====
  
Zeile 72: Zeile 72:
  
 {{ en:clt:hotspot:software:cltdesigner:manual:modul_tbeam:zusammenfassung.png |Summary of the results}} {{ en:clt:hotspot:software:cltdesigner:manual:modul_tbeam:zusammenfassung.png |Summary of the results}}
-===== Implemented calculation methods =====+/*===== Implemented calculation methods =====
  
 ++++ Effective width of T-beams made of CLT and GLT | ++++ Effective width of T-beams made of CLT and GLT |
Zeile 81: Zeile 81:
 {{page> :clt:design:tbeam:example&inline&permalink}} {{page> :clt:design:tbeam:example&inline&permalink}}
 ++++ ++++
 +
 +~~DISCUSSION~~*/
  • en/clt/hotspot/software/cltdesigner/manual/modul_tbeam.1522766586.txt.gz
  • Zuletzt geändert: 2018/04/03 16:43
  • von Alexandra Thiel