Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam [2017/11/16 12:08] – Alexandra Thiel | en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam [2020/03/24 10:37] – [My materials] Alexandra Thiel | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== Module | + | ====== Module |
{{ en: | {{ en: | ||
Line 37: | Line 37: | ||
The width of the CLT plate strips can be also defined in this field. The default value is set to 1 m. The thickness of the CLT plate is calculated automatically based on the thickness of the single layers. | The width of the CLT plate strips can be also defined in this field. The default value is set to 1 m. The thickness of the CLT plate is calculated automatically based on the thickness of the single layers. | ||
+ | |||
+ | The ratio of board thickness to board width can also be changed here. The default setting is 1:4. | ||
=== My CLT cross sections === | === My CLT cross sections === | ||
Line 50: | Line 52: | ||
* With {{: | * With {{: | ||
* With {{: | * With {{: | ||
+ | |||
+ | <WRAP center round info 100%> | ||
+ | **Syntax of the csv file** | ||
+ | |||
+ | name;number of layers n;layer thickness in [m] t< | ||
+ | |||
+ | Example: | ||
+ | Test layup; | ||
+ | </ | ||
+ | |||
+ | === My materials === | ||
+ | |||
+ | With the button {{: | ||
+ | |||
+ | {{ en: | ||
+ | |||
+ | * With {{: | ||
+ | * With {{: | ||
+ | * With {{: | ||
+ | * With {{: | ||
+ | * With {{: | ||
+ | |||
+ | <WRAP center round info 100%> | ||
+ | **Syntax of the csv file** | ||
+ | |||
+ | 1. row: description of the parameters\\ | ||
+ | 2. row: units of the parameters\\ | ||
+ | 3. row: value\\ | ||
+ | delimiter: ";" | ||
+ | |||
+ | Example: | ||
+ | Name; | ||
+ | ; | ||
+ | Mat 1; | ||
+ | </ | ||
+ | |||
+ | The user-defined materials are then displayed in the material selection list. | ||
+ | |||
+ | {{ en: | ||
+ | |||
+ | === Optimization of layup === | ||
==== Loads ==== | ==== Loads ==== | ||
Line 56: | Line 99: | ||
The plate weight is calculated automatically. The calculation method can be selected in the settings/ | The plate weight is calculated automatically. The calculation method can be selected in the settings/ | ||
- | * calculation based on the arithmetic average | + | * calculation based on the mean value of density of the chosen material |
* calculation based on a user-defined density | * calculation based on a user-defined density | ||
Line 98: | Line 141: | ||
For the vibration verification the following specifications are of importance: | For the vibration verification the following specifications are of importance: | ||
- | * high oder normal requirements? | + | * high or normal requirements? |
* modal damping factor | * modal damping factor | ||
* consideration of the screed (concrete topping) stiffness | * consideration of the screed (concrete topping) stiffness | ||
Line 104: | Line 147: | ||
* modulus of elasticity of the screed (concrete topping) | * modulus of elasticity of the screed (concrete topping) | ||
* support (2-sided or 4-sided) | * support (2-sided or 4-sided) | ||
- | * plate width b perpendicular to the load carrying direction | + | * room width b perpendicular to the load carrying direction |
The effective width b< | The effective width b< |